I. Assembly of Vane Pumps Cartridge Kits
1. All parts are cleaned
2.Place the oil pan 13 on a clean plate
3.After the rotor 14 is placed on the 13th part, insert all the blades 15 (12 in the picture) into the blade slots of the bottom 14
4. Put the stator ring on the rotor with blades installed 16
5. Insert the positioning pins 17 to 13: 0 while rotating 16
6. Position with the exposed two pins 17 and install in the oil distribution pan 18
7. Screw in the four hex screws 19 to screw the parts together, and put 0-rings 10 and 9 on the piece 13;
The Vane Pumps Cartridge Kits is assembled.
Repair of oil distribution pan
The total depth of the end-face strain is not too deep (for example, less than 1mm), and the groove marks can be removed by flat grinding, and polished and assembled before reuse.
Three. Repair of the rotor
The two end surfaces D and E of the rotor are moving sliding surfaces that are in contact with the end face of the oil distribution plate, so they are prone to wear and tear.
Fractures or cracks occurred in a small amount at the keyway. And the blade groove is widened and worn.
If only the two end surfaces are slightly worn, you can continue to use them after polishing; if the wear and tear is severe, you must use a spline mandrel and the center to position and clamp, and then polish the two end surfaces on a universal cylindrical grinder. However, it should be noted that the blades and stators should also be ground away at this time to ensure that the blade length is less than the thickness of the rotor 0.005 to 0.01 mm, and the thickness of the stator should be greater than the thickness of the rotor 0.03 to 0.04 mm.
Zhejiang Yongling Hydraulic Machinery Co., Ltd. is a professional China manufacturer and supplier of Vane Pumps Cartridge Kits . Welcome to buy our products: https://www.china-vanepump.com/product/t-series-pin-vane-pumps-with-high-pressure/t6c-t6cl-vane-pump-cartridge-kits.html
1. All parts are cleaned
2.Place the oil pan 13 on a clean plate
3.After the rotor 14 is placed on the 13th part, insert all the blades 15 (12 in the picture) into the blade slots of the bottom 14
4. Put the stator ring on the rotor with blades installed 16
5. Insert the positioning pins 17 to 13: 0 while rotating 16
6. Position with the exposed two pins 17 and install in the oil distribution pan 18
7. Screw in the four hex screws 19 to screw the parts together, and put 0-rings 10 and 9 on the piece 13;
The Vane Pumps Cartridge Kits is assembled.
Repair of oil distribution pan
The total depth of the end-face strain is not too deep (for example, less than 1mm), and the groove marks can be removed by flat grinding, and polished and assembled before reuse.
Three. Repair of the rotor
The two end surfaces D and E of the rotor are moving sliding surfaces that are in contact with the end face of the oil distribution plate, so they are prone to wear and tear.
Fractures or cracks occurred in a small amount at the keyway. And the blade groove is widened and worn.
If only the two end surfaces are slightly worn, you can continue to use them after polishing; if the wear and tear is severe, you must use a spline mandrel and the center to position and clamp, and then polish the two end surfaces on a universal cylindrical grinder. However, it should be noted that the blades and stators should also be ground away at this time to ensure that the blade length is less than the thickness of the rotor 0.005 to 0.01 mm, and the thickness of the stator should be greater than the thickness of the rotor 0.03 to 0.04 mm.
Zhejiang Yongling Hydraulic Machinery Co., Ltd. is a professional China manufacturer and supplier of Vane Pumps Cartridge Kits . Welcome to buy our products: https://www.china-vanepump.com/product/t-series-pin-vane-pumps-with-high-pressure/t6c-t6cl-vane-pump-cartridge-kits.html
コメント